- 您现在的位置：买卖IC网 > Sheet目录317 > CAT24C164YI-G (ON Semiconductor)IC EEPROM SERIAL 16KB I2C 8TSSOP
CAT24C164
WRITE OPERATIONS
Byte Write
In Byte Write mode, the Master sends the START
condition and the Slave address with the R/W bit set to zero
to the Slave. After the Slave generates an acknowledge, the
Master sends the byte address that is to be written into the
address pointer of the CAT24C164. After receiving another
acknowledge from the Slave, the Master transmits the data
byte to be written into the addressed memory location. The
CAT24C164 device will acknowledge the data byte and the
Master generates the STOP condition, at which time the
device begins its internal Write cycle to nonvolatile memory
(Figure 6). While this internal cycle is in progress (t WR ), the
SDA output will be tri ? stated and the CAT24C164 will not
respond to any request from the Master device (Figure 7).
Page Write
The CAT24C164 writes up to 16 bytes of data in a single
write cycle, using the Page Write operation (Figure 8). The
Page Write operation is initiated in the same manner as the
Byte Write operation, however instead of terminating after
the data byte is transmitted, the Master is allowed to send up
to fifteen additional bytes. After each byte has been
transmitted the CAT24C164 will respond with an
acknowledge and internally increments the four low order
address bits. The high order bits that define the page address
remain unchanged. If the Master transmits more than sixteen
bytes prior to sending the STOP condition, the address
counter ‘wraps around’ to the beginning of page and
previously transmitted data will be overwritten. Once all
sixteen bytes are received and the STOP condition has been
sent by the Master, the internal Write cycle begins. At this
point all received data is written to the CAT24C164 in a
single write cycle.
Acknowledge Polling
The acknowledge (ACK) polling routine can be used to
take advantage of the typical write cycle time. Once the stop
condition is issued to indicate the end of the host’s write
operation, the CAT24C164 initiates the internal write cycle.
The ACK polling can be initiated immediately. This
involves issuing the start condition followed by the slave
address for a write operation. If the CAT24C164 is still busy
with the write operation, NoACK will be returned. If the
CAT24C164 has completed the internal write operation, an
ACK will be returned and the host can then proceed with the
next read or write operation.
Hardware Write Protection
With the WP pin held HIGH, the entire memory is
protected against Write operations. If the WP pin is left
floating or is grounded, it has no impact on the operation of
the CAT24C164. The state of the WP pin is strobed on the
last falling edge of SCL immediately preceding the first data
byte (Figure 9). If the WP pin is HIGH during the strobe
interval, the CAT24C164 will not acknowledge the data byte
and the Write request will be rejected.
Delivery State
The CAT24C164 is shipped erased, i.e., all bytes are FFh.
http://onsemi.com
6
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CAT24C208WI-GT3
IC EEPROM SER 8KB 400KHZ 8SOIC
CAT24C21LI
IC EEPROM SERIAL 1KB DUAL 8PDIP
CAT24C256XI-T2
IC EEPROM 256KBIT 400KHZ 8SOIC
CAT24C32HU3I-GT3
IC EEPROM 32KB I2C SERIAL 8UDFN
CAT24C32TSI-T3
IC EEPROM SRL 32KB I2C 5TSOP
CAT24C512HU5IGT3
IC EEPROM SRL 512KB I2C 8UDFN
CAT24C512XI
IC EEPROM I2C SRL 512KB 8SOIC
CAT24C64ZI-GT3
IC EEPROM I2C SRL 64KB 8MSOP
相关代理商/技术参数
CAT24C164YI-GT3
功能描述:电可擦除可编程只读存储器 16K-Bit Serial Cascadable RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C16C4ATR
功能描述:电可擦除可编程只读存储器 16KB I2C SER 电可擦除可编程只读存储器
RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C16C5ATR
功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C16DWF
制造商:ON Semiconductor 功能描述:16KB I2C SER EEPROM - Rail/Tube
CAT24C16HU4I-GT3
功能描述:电可擦除可编程只读存储器 16KB I2C SER 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
CAT24C16HU4I-GT3JN
功能描述:IC EEPROM 16KBIT 400KHZ 8UDFN 制造商:on semiconductor 系列:- 包装:带卷（TR） 零件状态:有效 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:16K（2K x 8） 速度:400kHz 接口:I2C，2 线串口 电压 - 电源:1.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C（TA） 封装/外壳:8-UFDFN 裸露焊盘 供应商器件封装:8-UDFN-EP（2x3） 标准包装:3,000
CAT24C16LI
制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT24C16LI-G
功能描述:电可擦除可编程只读存储器 (2048x8) 16K 1.8-5.5 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8